Photo collection

Unit 1 power panel (P/C 1C-1) installation

 1. Power panel (P/C 1C-1) carried in from the opening of the Reactor Building annex

Photo taken on April 13, 2012 

2. Power panel (P/C 1C-1) carried down through the opening

Photo taken on April 13, 2012

3. Moving the power panel (P/C 1C-1) after it’s lifted down

Photo taken on April 13, 2012

4. Power panel (P/C 1C-1) installation completed on April 19

Photo taken on April 23, 2012

Function check of the residual heat removal cooling sea water system (B system)

1. Moving the electric motor of Unit 1 residual heat removal cooling sea water system (B system) from the 2nd floor to the 1st floor of the Sea Water Heat Exchanger Building

Photo taken on April 5, 2012

2. Installation of the electric motor of Unit 1 residual heat removal cooling sea water system (B system)

Photo taken on April 5, 2012

3. Function check after installation (Temperature measurement during the trial run)

Photo taken on April 12, 2012

4. Function check after installation (Vibration measurement during the trial run)

Photo taken on April 12, 2012

Permanent installation of Unit 4 residual heat removal cooling system, residual heat removal cooling sea water system and emergency diesel generator cooling system

Permanent installation of power panel (P/C 4D-2) has been completed on March 23, 2012

Photo taken on March 23, 2012

Switching to the permanent cable for the electric motor of residual heat removal cooling system pump (B system)

Photo taken on April 11, 2012

Switching to the permanent cable for the electric motor of residual heat removal cooling system pump (C system)

Photo taken on April 26, 2012

Switching to the permanent cable for the electric motor of residual heat removal cooling system pump (D system)

Photo taken on April 12, 2012

Switching to the permanent cable for the electric motor of residual heat removal cooling seawater system pump (B system)

Photo taken on May 8, 2012

Switching to the permanent cable for the electric motor of residual heat removal cooling seawater system pump (C system)

Photo taken on April 26, 2012

Switching to the permanent cable for the electric motor of residual heat removal cooling seawater system pump (D system)

Photo taken on April 25, 2012

Switching to the permanent cable for the electric motor of emergency diesel generator cooling system pump (B system)

Photo taken on April 12, 2012

Facilities subject to the visual inspection

1. PCV entrance (Airlock for workers）

Photo taken on April 17, 2012

2. Inside of PCV

Photo taken on April 17, 2012

3. Inside of PCV

Photo taken on April 17, 2012

4. Pedestal (Base structure of RPV)

Photo taken on April 17, 2012

5. Reactor recirculation pump

Photo taken on April 17, 2012

6. Main steam isolation valve

Photo taken on April 17, 2012

Issues detected (Press release issued on April 6, 2012)

7. Paint coming off on PCV inner surface

Photo taken on March 28, 2012

8. Rusted stud bolt on the reactor recirculation pump (B)

Photo taken on February 16, 2012

Inspection of the inside of Unit 4 main exhaust duct

1. Outer appearance of Unit 4 main exhaust duct

Photo taken on April 5, 2012

2. Inspection door of the main exhaust duct

Photo taken on April 5, 2012

3. Inspecting the inside of the main exhaust duct

Photo taken on April 5, 2012

4. Displacement measurement done on the main exhaust duct from April 19 to 26, 2012

Photo taken on April 24, 2012

Recovery work for Unit 1 D/G (A, H) flooded due to Tsunami

Flooded condition of Unit 1 D/G (A)

Photo taken on March 20, 2011

Recovery work for Unit 1 D/G (A)

Photo taken on April 17, 2012

Flooded condition of Unit 1 D/G (H)

Photo taken on March 20, 2011

Recovery work for Unit 1 D/G (H)

Photo taken on April 17, 2012

D/G in standby state after recovery 

Unit 1 D/G (B)

Photo taken on April 20, 2012 

Unit 2 D/G (A)

Photo taken on April 20, 2012

Unit 3 D/G (A)

Photo taken on April 17, 2012 

Unit 4 D/G (A)

Photo taken on April 17, 2012